Technical Commentary on Information Technology Equities -- Autodesk, Jabil Circuit, CDW, SunEdison, and RF Micro Devices

Editor Note: For more information about this release, please scroll to bottom

LONDON, July 18, 2014 — (PRNewswire) —

On Thursday, July 17, 2014, the NASDAQ Composite ended at 4,363.45, down 1.41%, the Dow Jones Industrial Average finished the day 0.94% lower at 16,976.81, and the S&P 500 closed at 1,958.12, down 1.18%. The losses were broad based as all the ten sectors edged lower. The S&P 500 Information Technology Sector Index ended the day at 641.50, down 1.31%, while the index has advanced 2.36% in the last one month. Investor-Edge has initiated coverage on the following equities: Autodesk Inc. (NASDAQ: ADSK), Jabil Circuit Inc. (NYSE: JBL), CDW Corporation (NASDAQ: CDW), SunEdison Inc. (NYSE: SUNE), and RF Micro Devices Inc. (NASDAQ: RFMD). Free research on these five companies can be accessed at:  

http://investor-edge.com/register

On Thursday, Autodesk Inc.'s stock recorded a trading volume of 2.87 million shares, higher than its three months average volume of 1.97 million shares. The stock finished the day flat at the previous day's closing price of $55.42, and registered an intraday range of $55.17 and $55.98. Autodesk Inc.'s shares have advanced 1.45% in the last one month and 14.29% in the previous three months. Also, the stock has surged 10.14% on YTD basis. Furthermore, the company's stock is trading above its 50-day and 200-day moving averages. The stock's 50-day moving average of $53.35 is above its 200-day moving average of $49.08. Additionally, shares of the company traded at a PE ratio of 60.46 and have a Relative Strength Index (RSI) of 52.57. Sign up and read the free notes on ADSK at:

http://www.Investor-Edge.com/ADSK-18Jul2014

Jabil Circuit Inc.'s stock declined 0.68%, to close Thursday's session at $20.44, after oscillating between

EDITOR'S NOTES:

===============

1. This is not company news. We are an independent source and our views do not reflect the companies mentioned.

2. Information in this release is produced on a best efforts basis by Rohit Tuli, a CFA charterholder. The content is then further fact checked and reviewed by an outsourced research provider. However, we are only human and are prone to make mistakes. If you notice any errors or omissions, please notify us below.

3. This information is submitted as a net-positive to companies mentioned, to increase awareness for mentioned companies to our subscriber base and the investing public.

4. If you wish to have your company covered in more detail by our team, or wish to learn more about our services, please contact us at pubco [at] http://www.investor-edge.com.

5. For any urgent concerns or inquiries, please contact us at compliance [at] http://www.investor-edge.com.

6. Are you a public company? Would you like to see similar coverage on your company? Send us a full investors' package to research [at] http://www.investor-edge.com for consideration.

COMPLIANCE PROCEDURE

Content is researched, written and reviewed on a best-effort basis. This document, article or report is prepared and authored by Investor-Edge, represented by Rohit Tuli, CFA. An outsourced research services provider has only reviewed the information provided by Investor-Edge in this article or report according to the procedures outlined by Investor-Edge. Investor-Edge is not entitled to veto or interfere in the application of such procedures by the outsourced provider to the articles, documents or reports, as the case may be.

NOT FINANCIAL ADVICE

Investor-Edge makes no warranty, expressed or implied, as to the accuracy or completeness or fitness for a purpose (investment or otherwise), of the information provided in this document. This information is not to be construed as personal financial advice. Readers are encouraged to consult their personal financial advisor before making any decisions to buy, sell or hold any securities mentioned herein.

NO WARRANTY OR LIABILITY ASSUMED

Investor-Edge is not responsible for any error which may be occasioned at the time of printing of this document or any error, mistake or shortcoming. No liability is accepted by Investor-Edge whatsoever for any direct, indirect or consequential loss arising from the use of this document. Investor-Edge expressly disclaims any fiduciary responsibility or liability for any consequences, financial or otherwise arising from any reliance placed on the information in this document. Investor-Edge does not (1) guarantee the accuracy, timeliness, completeness or correct sequencing of the information, or (2) warrant any results from use of the information. The included information is subject to change without notice.

CFA® and Chartered Financial Analyst® are registered trademarks owned by CFA Institute.

 

SOURCE Investor-Edge

Contact:
Investor-Edge
Adam Redford
Phone: +852-8191-3972

 

Featured Video
Jobs
Senior Principal Software Engineer for Autodesk at San Francisco, California
Machine Learning Engineer 3D Geometry/ Multi-Modal for Autodesk at San Francisco, California
Principal Engineer for Autodesk at San Francisco, California
Business Development Manager for Berntsen International, Inc. at Madison, Wisconsin
Mechanical Engineer 2 for Lam Research at Fremont, California
Equipment Engineer, Raxium for Google at Fremont, California
Upcoming Events
Dimensions User Conference 2024 at The Venetian Resort Las Vegas NV - Nov 11 - 13, 2024
Greenbuild 2024 at Pennsylvania Convention Center Philadelphia PA - Nov 12 - 15, 2024
Digital Construction North (DCN) 2024 at Manchester Central. Manchester United Kingdom - Nov 13, 2024
Digital Twins 2024 at the Gaylord National Resort & Convention Center in, MD. National Harbor MD - Dec 9 - 11, 2024



© 2024 Internet Business Systems, Inc.
670 Aberdeen Way, Milpitas, CA 95035
+1 (408) 882-6554 — Contact Us, or visit our other sites:
TechJobsCafe - Technical Jobs and Resumes EDACafe - Electronic Design Automation GISCafe - Geographical Information Services  MCADCafe - Mechanical Design and Engineering ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy PolicyAdvertise